Magnetic MHTM FlowMotion mTripod Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 84

Magnetic MHTM FlowMotion mTripod Скачать руководство пользователя страница 43

43

mTripod

Installation and assembly

IMPORTANT!
Follow the separate notes and instructions for the composite

mortar and foundation anchors.

ä

Foundation and empty conduit plan mTripod FMTP-ML: Page 35, Fig. 6.

ä

Foundation and empty conduit plan mTripod FMTP-MS: Page 37, Fig. 8.

1. Drill the boreholes for the female threaded sleeves according to the

foundation plan.
NOTICE

Wrong orientation of the turnstile! The turnstile is not symmetrically

constructed. Align the turnstile so that the passage side is on the correct

side. Observe foundation plan.

2.  Clean the boreholes with compressed air.
3.  Inject composite mortar into the boreholes.
4.  Female threaded sleeves with internal thread to the bottom of the

boreholes by hand. The BSS100 mounting kit contains mounting aids.

5.  Wait for the curing time. Follow separate instructions.
6.  Position turnstile.
7.  Place U-profiles, washers and hexagonal screws.

WARNING

Possible injuries due to falling pedestrian gate!

Use screws M8 x 30 from attachment set BSS100. Do not use the M8 x 16

screws.

8.  Slightly tighten the screws.
9.  Align turnstile.
10.  Tighten the screws firmly.
11.  If necessary, seal the housing with a silicone joint.
12.  Arrange electrical connections.

ä

Page 62, chapter 8.

13. Mount the holding bracket, trapezoidal plate, front panel, cover and

locking arms.

ä

Page 52, chapter 7.9.

«
...
41
42
43
44
45
...
»

Содержание MHTM FlowMotion mTripod





















































































Отзывы:

Нет отзывов