Magnetic MHTM FlowMotion mTripod страница 64 Скачать руководство пользователя

Страница: 64 / 84

mTripod

Electrical connection

8.3

Connecting the mains cable

IMPORTANT!
The wire cross-section of the mains cable must be between 1.5

and 4 mm². Observe national provisions on line length and

associated line cross-section.

Prerequisites

›

The housing is open.

Page 60, chapter 7.11.

1. Disconnect the system from the power supply. Ensure that the system is

powered down. Secure against reactivation.

DANGER

Mortal danger by electric voltage!

2. Strip mains cable and strands according to the following figure.

Mag0081

Fig. 32:  Stripping (dimensions in mm)
1  Phase
2  Zero conductor
3  Protective earth conductor

3. Carefully lead the mains cable through the housing to the connection

compartment and fasten it with the brackets.

4. Connect the mains cable to the terminals X1: Connect L / N / PE.

Wiring

diagram, separate document.

5. Attach mains cable to the tabs with 2 cable ties.

Содержание MHTM FlowMotion mTripod





















































































Результаты поиска

Содержание MHTM FlowMotion mTripod

Отзывы:

Похожие инструкции для MHTM FlowMotion mTripod

Бренды по названию

Популярные бренды

Magnetic MHTM FlowMotion mTripod, Руководство по эксплуатации

Результаты поиска

Содержание MHTM FlowMotion mTripod

Отзывы:

Похожие инструкции для MHTM FlowMotion mTripod

Бренды по названию

Популярные бренды