(E)
7-19
7. Operation Method
LH71A / LH72
1. Cautions
•
Before use, be sure to turn the steel ball with the fingers about the axis of the shaft 2 or 3 times both
clockwise and counterclockwise so that the steel ball rests properly on the end of the shaft.
If this not done, the rust-preventive grease between the steel ball and shaft might cause a detection error.
•
Do not turn the steel ball more than 180º in either direction since a spring is connected to it.
•
Do not pull the steel ball and let it spring back sharply against the end of the shaft.
•
Fix the shank to the main spindle in such a way that the shank is not inclined against the axis of the
spindle, since inclination of the shank will cause errors in the measurement.
•
For more precise positioning at the center of the workpiece: Touch the workpiece with the feeler ball
q
.
Then, move the touch sensor to the other side of the workpiece, rotate the shank holder of the machine
through 180º and then touch the workpiece
w
. Half the measured value is the center of the workpiece.
Spring
Dust cover
Workpiece
Axis of spindle
Axis of spindle
Center
Rotate the shank holder of the machine
through 180° and then touch the workpiece.
Steel ball
Shaft
Give a 180º turn 2 to 3 times
(No more than 180º)
q
w
Содержание LH71A
