5-8
(E)
LH71A / LH72
q
w
e
r
t
y
u
i
o
or
or
Basic
settings
Detailed
settings
Model
Destination
country
Scaling
(1.000000)
Measuring
unit
resolution
Display
resolution
(Measuring unit
resolution)
Compensation
value
(OFF)
Flicker control
(2)
Sleep
(OFF)
Addition
display
Approx.
2 seconds
Power ON
Enter the setting value
Select axis
Select axis
or
or
Standby key lamp
(Lights up
→
flashes)
Start of operation
(When the display resolution is 0.001 mm)
∗
When the segmented error compensation value is set, is displayed,
the unit switches to reference point acquisition mode.
(Hold down for
approx. 3 s.)
∗
The setting in parentheses ( ) is the factory setting.
∗
indicates the process when the setting does not
be changed.
Use to select
Use to select the settings for display 2
Performed for each axis.
Use to select setting content
Use to select setting content
Use to expand the selection option.
Use and to select setting content
Performed for each axis.
Use to select the setting (compensation), and then set each option
Enter the compensation value
Enter the
compensation value
Enter the
position
Select axis
Use to select setting content
Use to select setting content
(Note)
Use at
Note 1
Note 1: Pressing or cancels the changes
in the “basic settings”, and switches the
setting mode to “detailed settings”.
5-3-2. Resetting the Basic Settings
(LH71A lathe function and LH72)
When the basic settings are reset, all detailed settings will revert to their factory default settings.
q
Select LATHE
(LH71A only)
∗
The LH72 does
not have a
model setting.
w
2/3/2ADD3/
2ADD–3/
–2ADD3/
–2ADD–3
∗
See Part 5-4,
“Verifying Count
Values during
Addition
Display”.
e
STD/US/JPN
r
0.1/0.5/1/5/10/
00.00.01/
00.00.10/
00.01.00/
00.10.00
<Expanded>
0.05/2/20/25/50/
100/01.00.00
t
Setting at
r
or
higher/Diameter
display at
r
(except for
angle)/Polarity
∗
The X-axis
polarity should
be set so that
the value of the
cutting direction
decreases when
using diameter
display.
y
0.100000 -
9.999999
u
OFF/LIN Err/
SEG Err
∗
See Part 5-5,
“Compensation”.
i
OFF/1/2
o
OFF/1/5/10/30/
60
∗
If you have already entered the “detailed settings”, make a note of the
setting values before resetting or changing the “basic settings”.
5. Settings
Содержание LH71A
