background image

3. Operation Fault

Corrective Actions:

1. Make sure that the currency counter is 

plugged into a wall outlet and that the 
power cord is plugged into the back of 
the machine.

2. Check that the voltage selection switch 

matches power input.

Call for service.
Turn off and unplug the currency counter. 
Call for service.
CAUTION  
• DO NOT insert tools into the currency 

counter. Doing so many damage the 
machine.

• DO NOT use oil on any part of the 

currency counter. Oil on sensors or 
internal mechanisms can prevent 
correct operation.

Fault

Currency counter 
does not power up 
when machine is 
turned on.

Self-test failure.
Electrical burn orders.

Loud buzzing slapping 
or other unusual 
noises during the 
operation.

IMPORTANT

If the corrective actions suggested here do not solve the problem, 

call your service representative.

VIII. Cleaning Jams Manually

-  Record the running and grand totals.
-  Turn the power switch off.

 NOTE

Turning off the currency counter clears the memory of totals.

-  Remove  all  notes  from  the  hopper  and  stacker. Also,  remove  notes  from 

inside the currency counter by using the Note jam release lever. 

-  Push the Note jam release lever all the way up.
-  If  it  is  necessary  to  keep  locking  up  the  Note  jam  release  lever  to 

release jam note(s), insert a coin into the slot.

-  Make  sure  that  the  Note  jam  release  lever  is  returned  to  the  original 

position after jam note(s) is cleared.

14

Содержание 35-2003 Series





















Отзывы: