RS 350 M / RS 400 M / RS 500 M / RS 400 MW / RS 500 MW
42
2.2 INSTALLATION AND WORKING RECOMMENDATIONS
Ÿ
When the gas cylinder is placed on the machine,
immediately lock the chain to secure the cylinder,
otherwise, the stand alone cylinders should also be
secured to a wall by chains.
Ÿ
The electrical socket behind the machine is for
the
CO heater. DO NOT CONNECT ANY OTHER
2
DEVICE TO
THE
CO
HEATER
!
2
2.3 ELECTRIC PLUG CONNECTION
Ÿ
Since mains connection sockets may vary from
factory to factory, an appropriate plug must be
installed to the built-in mains cable of the machine
by qualified electricians. Please observe that the
earth cable is in yellow/green colour and labelled
as . After installing the electric plug, DO NOT
INSERT IT INTO THE SOCKET AT THIS STAGE.
Figure 5:
Electric Plug Connection
2. INSTALLATION
INSTALLATION
2.1 UPON RECEIPT AND CLAIMS
Ÿ
Be sure that you have received all the items that
you have ordered. In case of any item is missing or
damaged, contact your supplier immediately.
Ÿ
In the event of damaged or missing delivery,
draw
up a record, take a photo of the damage and
report
it to the shipping agency and MAGMA
MEKATRONIK with the photocopy of shipping bill.
E-mail: [email protected]
Fax: +90 236 226 27 28
Ÿ
Standard pallet contains:
ú
Power Source
ú
Wire Feeder Unit
ú
Water Cooling Unit (only for MW models)
ú
Earth Cable
ú
Gas Hose
ú
User Manual
Ÿ
Use lifting eyes or fork-lift to carry the machine. DO
NOT lift the machine together with the gas
cylinder.
Ÿ
Transport and place the device on a firm and level
ground so that it may not fall over. The maximum
permissible angle of inclination for transport and
assembly is 10°.
Ÿ
For a better performance, keep the machine at
least 30 cm away from the surrounding objects.
Beware of excessive dust and humidity around the
machine.
Ÿ
Do not place any heat source in front of the
machine where the cooling air enters. Do not
operate the machine under direct sunlight.
Machines should be operated on
lower
capacities
when ambient air temperature
exceeds
40ºC
.
Ÿ
Avoid welding at outdoors where it is windy and
rainy, if this is a must, protect the welding area with
curtains, mobile screens or tents.
Ÿ
While welding indoor, use a suitable welding fume
extraction system. Use breathing apparatus if
there is a risk of inhaling in confined places.
Ÿ
Respect the duty cycles given at the
data plate. Exceeding the duty cycles
frequently can damage the machine
and this would void the warranty.
Ÿ
Do not use stronger fuses than those
stated on the data plate in the user
manual.
Ÿ
Ensure that the earth clamp is tightly
connected as close as possible to the
welding location. Do not let welding
current flow through any media other
than welding cables; e.g. over the
machine itself, gas tubes, chains, ball
bearings, etc.
Содержание RS 350 M
