• Magma On-Board LPG (Propane) Valves & Hose Kits allow
Magma Grills to be installed within a boats existing
on-board, pre-regulated low pressure LPG (Propane) system.
• Use only
Magma Type 3 Low Pressure LPG (Propane)
Valves.
See our
Valve Application Guide
at
MagmaProducts.com
for correct valve.
• In North America use
Magma A10-225 LPG 10' Gas
Grill Connection Kit
in conjunction with
Type 3 Valve.
Outside North America check your local dealer for proper
hose and fittings.
• A primary shutoff valve
(supplied with Gas Grill
Connection Kit)
must be used with this control valve at
point of connection into your system. This allows shut off
of gas supply to hose leading to grill.
•
In Australia & New Zealand LPG fuel systems must
be installed by a certified gas technician.
Stainless Steel, contrary to popular belief, can rust. Most commonly, deposits on the surface of the product will trap
moisture. It is this moisture that robs the stainless steel of oxygen. Oxygen is the element that reacts with the stainless
steel to form a protective layer of chrome oxide. Robbed of oxygen this reaction does not take place and “crevice
corrosion”, or “surface rusting”, occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse
with fresh water and dry. Avoid using products designed to clean stainless steel as most leave a residue that may discolor
when the grill is heated.
Additionally, stainless steel that is exposed to high heat will change in color and texture over time. This “bluing” and
later “browning” of the internal components is not a failure of the stainless steel and will not affect the product
operation. However, prolonged exposure to extreme high heat will cause the chromium and nickel to “burn out” of the
stainless steel. At this point the stainless steel will become more susceptible to corrosion and will start to deteriorate. We
recommend that you replace these internal components if they become seriously deteriorated.
We recommend thorough cleaning of all internal parts after each outing. It is important to disassemble the interior
components and remove any food residue. A soft “Scotch-Brite” pad or similar product may be used in this process. For
heavier burned-on stains we recommend “Easy-Off Oven & Grill Cleaner” followed by thorough washing with soap and
water, rinse with fresh water and dry. AVOID CONTACT OF OVEN CLEANER WITH CONTROL VALVE, IGNITER
ELECTRODE & WIRE, AND BOAT SURFACES. CAUTION: DO NOT USE ANY TYPE OF ABRASIVE PAD ON THE EXTERIOR
MIRROR FINISH AS IT WILL SCRATCH THE SURFACE. USE ONLY A SOFT COTTON CLOTH. We recommend covering the
grill between uses. Grill covers are available at Magma retailers or directly from Magma. See our website,
MagmaProducts.com.
Grill Grates
-
Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash with
soapy water and dry prior to storage.
Control Valve
-
All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any
way. Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing
the orifice.
Repair/Replacement Parts -
All replacement parts are readily available at your Magma Retailers or directly from
Magma. For a complete list of replacement parts visit our website
MagmaProducts.com.
Align valve stem key
to valve chamber
lock detent and rotate
Gas Grill
Propane (LPG)
Gas Regulator
A10-225
Hose Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gas Grill
Type 3
Valve
Type 3
Valve
Solenoid
Gas Grill
Typical Marine &
R.V. Application
Align valve stem key
to valve chamber
lock detent and rotate
Gas Grill
Propane (LPG)
Gas Regulator
A10-225
Hose Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gas Grill
Type 3
Valve
Type 3
Valve
Solenoid
Gas Grill
Typical Marine &
R.V. Application
Insert valve as shown in diagram above. Valve
may seem loose, this is OK. Valve does not have
to be snug-fitting to be safe or function properly.
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
MAINTENANCE
7
