Magliner Powered Stair Climber Скачать руководство пользователя страница 30

Страница: 30 / 50

Motor Components

Motor Safety Cover

005025

Motor mount bushing -

27mm

005028

Drive Motor Sal 110

010123

Drive Motor Sal 140

010124

Drive Motor Sal 170

010137

Motor Safety Cover Spring, Powered Stair Climber

005033

Rod, lifting unit mount

030132

Lifting Unit Sal 110

005133

Lifting Unit Sal 140

005134

Lifting Unit Sal 170

005146

Drive Chain

005627

Bushing, Pivot Shaft

005610

Bushing, LH Motor Mount

005027

Black Plastic Cap for Safety Flap

005632

Safety Flap Shaft

005031

Nut M8, motor mount

005611

22. Powered Stair Climber Warranty and Liability

Warranty

The warranty period for the Powered Stair Climber is 12 months (6 months for batteries)
from the date of purchase and covers defective material and production faults.

Warranty exclusions are:



Normal wear and tear on parts



Damage resulting from abnormal load



Damage due to the exertion of force



Modifications to the Powered Stair Climber or its accessories

Liability

Magline Inc. as distributor of the Powered Stair Climber is not responsible for the safety of
the Powered Stair Climber if:



The Powered Stair Climber is used for purposes other than those for which it is intended



The Powered Stair Climber is not regularly maintained properly by a mechanical
workshop



The instructions in the operator manual are not observed



Non-original parts are installed or connected to the Powered Stair Climber



Original parts are removed

Содержание Powered Stair Climber


















































Результаты поиска

Содержание Powered Stair Climber

Отзывы:

Бренды по названию

Популярные бренды

Magliner Powered Stair Climber, Руководство по эксплуатации для пользователя

Результаты поиска

Содержание Powered Stair Climber

Отзывы:

Бренды по названию

Популярные бренды