background image

Installation

 

MKE Series Electric Griddle 
 

L20-369 REV. 2  (05/12) 

6

1/2" BOLTS (4)

BRACKET (2)

MOUNT FLUSH

TO FRONT

(SUPPLIED)

(SUPPLIED)

NUTS & BOLTS

INCLUDED

WITH STAND

REAR

 

Figure 4 

NOTICE

 

The larger units have 6 threaded receiving holes, but require only the four 1/2" bolts on each corner to 

mount the griddle.

 

1.  Remove (4) existing 1/4-20 nuts and bolts from the rear corners of the equipment stand. 
2.  Align the 2 bolt holes on the rear corners of the stand with the 2 bolt holes on the rear mounting brackets. 

Orient the brackets as shown in Figure #4 
on this page. 

3.  Install the provided rear mounting brackets 

(2) to the rear corners by using the existing 
1/4-20 hardware that were removed in step 
1, tighten securely. 

4.  Carefully place the griddle on the 

equipment stand. 

5.  Position the griddle so that the front edge of 

the base is flush with the front of the 
equipment stand. If the griddle is the only 
appliance to be mounted on the stand, then 
both sides of the griddle should be flush 
with the sides of the equipment stand.  

6.  When positioned properly, the threaded 

receiving holes in the griddle base should 
be aligned with mating clearance holes at 
the front of the equipment stand, and with 
the clearance holes in the rear mounting 
brackets. Install the provided 1/2" bolts and 
tighten securely. 

 

1.3.4. Leveling 

Instructions 

NOTICE 

Equipment stands are shipped from the 

factory with the legs or casters set to “Zero”. 

Units should be leveled at time of 

installation, failure to do so could cause the 

griddle to operate improperly. 

 
1.  Identify the end or corner of the stand that 

needs to be raised, remove the weight load 
from the caster or leg to be leveled. 

2. 

Legs-

 using a wrench, or pliers turn the leg 

bullet, See Figure 5, CCW to raise the 
height of the equipment stand. There is ½” 
to ¾” (1.3 – 1.9 cm) of adjustment. 

Casters-

 (For Stands shipped after May 

2006) Using a Flat Head screwdriver, 
loosen the set screws of the caster to be 
leveled, See Figure 5.Turn the collar of the 
caster CCW to raise the height of the 
equipment stand. There is ½” to ¾” (1.3 – 
1.9 cm) of adjustment. 
After leveling adjustment is complete, re-

tighten set screws. 
3.  Repeat Step 2 for legs or casters that require leveling. 
4.  Check the levelness of the equipment, if necessary Repeat steps 1, 2, and 3. 

 

Figure 5 

Содержание MKE SERIES

























Отзывы: