background image

Quick Start Guide 

Ultra Electronics Card Systems 

Page 22 

MAGICARD Sicura Laminator 

 

Notice 

The information contained in this document is subject to change without notice. 

Ultra Electronics Limited shall not be liable for errors contained herein or for incidental consequential 
damages in connection with the furnishing, performance or use of this material. 

This document contains proprietary information belonging to Ultra Electronics Limited and may not 
wholly or partially be copied, stores in a data retrieval system, disclosed to third parties or used for any 
purpose other than that for which it was supplied, without the express written authority of Ultra 
Electronics Limited.  All rights are reserved. 

©Ultra Electronics Limited, 2002

 

Federal Communications Commission (FCC) Statement

 

Warning: This equipment generates, uses, and can radiate radio frequency energy and if not installed 
and used in accordance with the instructions manual, may cause interference to radio 
communications. It has been tested and found to comply with the limits for a Class A computing 
device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable 
protection against such interference when operating in a commercial environment.  

Operation of this equipment in a residential area is likely to cause interference in which case the user 
at his own expense will be required to take whatever measures may be required to correct the 
interference. 

Note: Changes or modifications not expressly approved by the party responsible for compliance could 
void the user's authority to operate this equipment. 

Canadian Department of Communications Statement

 

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital 
apparatus set out in the Radio Interference Regulations of the Canadian Department of 
Communications. 

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicable 
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique 
édicté par le ministère des Communications du Canada. 

WINDOWS is a trademark of Microsoft Corporation. 
MAGICARD , Sicura and UltraSecure are trademarks of Ultra Electronics Limited. 
PrintMagic is a trademark of Software 2000 Limited. 
IBM, AT and PC are trademarks of International Business Machines Inc. 

 

Содержание MAGICARD Sicura Laminator

























Отзывы: