Mafell MF 26 cc, Оригинальная инструкция по эксплуатации

Страница: 26 / 34

-26-
4.5 Selection of tools
-
Saw blade-TCT Ø 120 x 1.8 x 20 mm (4 47/64 x
5/64 in. x 20 mm), 12 teeth
-
Saw blade-TCT Ø 120 x 1.8 x 20 mm (4 47/64 x
5/64 in. x 20 mm), 24 teeth
-
Saw blade-TCT Ø 120 x 1.8 x 20 mm (4 47/64 x
5/64 in. x 20 mm), 40 teeth
-
Saw blade-TCT Ø 120 x 1.2 x 20 mm (4 47/64 x
3/64 in. x 20 mm), 40 teeth
-
Slitting unit MF-SE3
-
Adjustable groove cutter MF-VN25
-
Plasterboard milling cutter MF-GF90/15
-
Aluminium compound milling cutter MF-AF90
See also the table in chapter 9.
4.6 Tool change to saw blade, plasterboard
milling cutter or aluminium compound
milling cutter.
Danger
Pull the power plug during all
service work.
The chip deflector must be
unscrewed prior to a tool change.

Using the Allen key 4 (bracket Fig. 2), unscrew
the countersunk screw with chip deflector 44
(Fig. 11).

To change the tools, place the machine with the
marking 17 (Fig. 1) or splinter guard 38 (Fig. 4)
on the edge of a support surface so that the
cover can tilt across the edge when it is opened.

To fold the saw guard cover 23 (Fig.4) down on
the side, press push-button 2 (Fig. 5). With
depressed push-button, pull locking lever 3
upwards. Pulling the locking lever automatically
locates the shaft in position and locks the
gearshift lever 8 (Fig. 5).

Using the Allen key 4 (brackets Fig. 2), release
the flange screw 5 (Fig. 4)
counter clockwise .
Pull off the slitting unit or adjustable groove
cutter to the front.

Push the rear flange 29 (Fig. 8) onto the shaft (if
not present).

The clamping flanges must be free of adhering
parts.

Place the saw blade, the plasterboard milling
cutter or the aluminium compound milling cutter
onto the rear flange 29 (Fig. 8).

When fitting the tool, pay attention to the sense
of rotation (see direction of arrow on the casing
and on the cover).

Push the clamping flange and flange screw onto
the tool.

Tighten the flange screw by turning it
clockwise
with the Allen key.

Close the saw guard cover. To this end, close
the cover and press the locking lever 3 (Fig. 5)
downwards.

The chip deflector must always be fitted when
milling aluminium compound panels.
4.7 Tool change to slitting unit or adjustable
groove cutter
Danger
Pull the power plug during all
service work.
The chip deflector must be
unscrewed prior to a tool change.

To change the tools, place the machine with the
marking 17 (Fig. 1) or splinter guard 38 (Fig. 4)
on the edge of a support surface so that the
cover can tilt across the edge when it is opened.

To fold the saw guard cover 23 (Fig.4) down on
the side, press push-button 2 (Fig. 5). With
depressed push-button, pull locking lever 3
upwards. Pulling the locking lever automatically
locates the shaft in position and locks the
gearshift lever 8 (Fig. 5).

Using the Allen key 4 (brackets Fig. 2) release
the flange screw 5 (Fig. 4)
counter clockwise.

Remove the flange 6 (Fig. 4) and the flange
screw 5 (Fig. 4).

Remove the rear flange 29 (Fig. 8) (if present).