Maeda MC174 Скачать руководство пользователя страница 15

- 13 - 

[CHECKING AFTER STARTING ENGINE] 

Check the following in this section after starting the engine and before starting the first work every day. 

CAUTION 

The checkups described in this section should be carried out after starting the machine. 
Refer to "Starting the Engine in the MC-174C Operation Manual page 3-54" and later to execute 
the engine startup, traveling operations, outrigger operations and crane operations.  

 

[1] CHECKING FUNCTIONS OF BOOM 

 

At the performance of function check for boom, ensure the safety so that hook and boom do not 
interfere with any personnel or object. 

 

1. Check abnormal noise from boom and searcher hook during 

crane operation.   

 

2. Operate crane without load and check each bolt so that no one 

is missing or loose. 

 

3. Check hook for deformation, abnormal noise from bearing and 

correct function of wire rope latch (1).   

 

[2] CHECKING MOMENT LIMITER FOR OPERATION (SEARCHER HOOK MODE) 

 

If you find any abnormality with the moment limiter, immediately contact us or our sales service 
agency.  

 

1. Turn the starter switch to the “ON” position. 

2. Check with the working status lamp. The red of the lamp lights up for 2 seconds and then the green 

lights up. 

3. Check the moment limiter display unit. 

Verify that no error codes are displayed on the “RATED TOTAL LOAD” display. 

4. Shift the fall mode selector switch on moment limiter display unit to ”Searcher hook mode” (all LED 

ON).  

5. Start the engine and operate the crane as follows to verify that the moment limiter properly displays 

the value. 

Crane Operation and Displayed Parameter 

Value Displayed on 

 Moment Limiter 

Displayed “boom length” with the boom length at minimum 

1.8 m 

Displayed “boom length” with the boom length at maximum 

5.5 m 

Displayed “working radius” with the boom length of “2.9 m” and boom angle of 
“55.5 °“ 

1.5 ± 0.1 m 

Displayed “ACTUAL LOAD” when the weight of the known weight was hoisted

Must be equal to the total weight of  lifting ring 
Note that it may show some errors depending on the boom conditions.

 

Actual load 

6. Operate the crane until the moment limiter display indicates the boom length is "2.9 m" (booms (1) + 

(2)) and boom angle is "55.5 degrees", then measure the "boom angle" and "working radius.  

If the measured value(s) differ from the moment limiter display value, contact MAEDA or MAEDA  

sales agency. 

Содержание MC174


















Отзывы: