
1.4 PRECAUTIONS WHEN GETTING ON OR OFF
USE HANDRAILS AND STEPS WHEN GETTING ON OR OFF
To prevent personal injury caused by slipping or falling off the
machine, always do as follows.
• Use the handrails and steps marked by arrows in the diagram on
the right when getting on or off the machine.
• To ensure safety, always face the machine and maintain
three-point contact (both feet and one hand, or both hands and one
foot) with the handrails and steps (including the track shoe) to
ensure that you support yourself.
• Before getting on or off the machine, check the handrails and steps
(including the track shoe). If there is any oil, grease, or mud on the
handrails and steps (including the track shoe), wipe it off
immediately. Always keep these parts clean. Repair any damage
and tighten any loose bolts.
• Do not grip the control levers, or lock lever when getting on or off
the machine.
• Never climb on the engine hood or covers where there are no
non-slip pads.
• Do not get on or off the machine while holding tools in your hand.
• Never jump on or off the machine, Never jump on or off a moving
machine.
• If the machine starts to move when there is no operator on the
machine, do not jump on to the machine and try to stop it.
PRECAUTIONS WHEN LEAVING OR STANDING UP FROM OPERATOR’S SEAT
• Before standing up from operator’s seat (such as when adjusting
the operator’s seat), always store the crane completely, set lock
lever (1) securely to the LOCK position (L), then stop the engine. If
you accidentally touch the control levers or pedals when they are
not locked, there is a hazard that the machine may suddenly move
and cause serious injury or property damage.
• When leaving the machine, always store the crane completely, set
lock lever (1) securely to the LOCK position (L), then stop the
engine. Use the key to lock all the equipment. Always remove the
key, take it with you, and keep it in the specified place.
EMERGENCY EXIT OF THE OPERATOR'S CABIN
• In an emergency where the cabin door is blocked or does not open,
use the emergency hammer and smash the windowpane so that
you get out of the cabin through it.
• When you go through, remove fragments of the windowpane to
prevent injury from them. In addition, take care of your footpath to
avoid slipping on fragments of that.
2-6
Содержание LC785M-8B
