background image

8

OPERATION MANUAL

5. OPERATION

This machine may perform many types of operations that are beyond the scope of this manual. 

Many of these operations may be dangerous or deadly if performed incorrectly.

The instructions in this section are written with the understanding that the operator has the

necessary knowledge and skills to operate this machine. If at any time you are experiencing

difficulties performing any operation, stop using the machine!

u

pper

 r

oller

l

ower

 r

oller

w

ork

 t

able

r

ear

 r

oller

H

anD

 C

rank

r

aDial

 

a

Djustment

t

HiCkness

 

a

Djustment

If you are an inexperienced operator, we strongly 

recommend that you read books, trade articles, or 

seek training from an experienced operator before 

performing any unfamiliar operations. 

Above all, 

your safety should come first! 

Thickness Adjustment Knob

. Raises and lowers

the upper roller to adjust for the thickness of 

different workpieces. (Fig. 3)

Radius Adjustment Knob.

 Raises and lowers

the rear roller to create smaller and larger radius

bends. (Fig. 3)

Hand Crank

: Rotates the rollers to feed the

workpiece through the machine. (Fig. 3)

FLAT ROLLING (FIG.4)

Lower the rear roller below the workpiece

path. This will prevent the rear roller from 

bending a curve in the workpiece as it is fed 

through the slip roll.

CURVE ROLLING (FIG.5)

 Use the thickness adjustment knobs to adjust

the height so that you can place the workpiece 

between the rollers. Rotate the radius adjustment 

knobs counterclockwise to raise the rear roller

F

ig

. 3

F

ig

. 4

F

ig

. 5

Содержание Hafco Metalmaster S267















Отзывы: