background image

Manual Sheetmetal Rolls Safety Instructions

1.   Maintenance. 

Make sure all moving parts are 

locked down before any inspection, adjustment or 

maintenance is carried out.

2.  Rolling machine Condition. 

Rolling machine must 

be maintained for a proper working condition. Never 

operate a Rolling machine that has damaged or 

worn parts. Scheduled routine maintenance should 

performed on a scheduled basis.

3.  Roll Condition. 

Never operate a Rolling machine 

with a damaged or badly worn Rolls. Replace if 

required. Rolls should never be greased or lubricated 

as rolls will slip the material and will not bend.

4.  Hand Hazard. 

Keep hands and fingers clear from 

moving parts. Serious injury can occur if hand or 

finger tips get pinched by rolls and can be dragged 

into machine.

5.  Gloves & Glasses. 

Always wear leather gloves and 

approved safety glasses when using this machine.

6.  Avoiding Entanglement. 

Rolling machine guards 

must be used at all times. Tie up long hair and use 

the correct hair nets to avoid any entanglement with 

the Rolling machine moving parts. 

7.  Understand the machines controls. 

Make sure you 

understand the use and operation of all controls.

8.  Work area hazards. 

Keep the area around the 

Rolling machine clean from oil, tools, chips. Pay 

attention to other persons in the area and know what 

is going on around the area to ensure unintended 

accidents.

9.   Guards. 

Do not operate this machine without the 

correct guards in place. Necessary guards protect 

you from injuries by rolls and moving gears and 

parts.

10.  Material condition. 

Material must be clean out of 

oil and dry. Oily material can slip and will not bend.

11.  Material hardness. 

Make sure your hardness is 

the same throughout the material, we recommend 

that you use certified material. Never bend hard 

steel, glass or fragile material on this machine.

12.  Level machine. 

Level the machine on a flat 

concrete surface by using a spirit level. 

13.  Feeding material. 

Making a tight bend in one pass 

is not possible. So you need several passes before 

you can achieve a certain radius. Tighter curves 

and full radius always need more passes. 

14.  Call for help. 

If at any time you experience 

difficulties, stop the machine and call you nearest 

branch service department for help.

Machinery House  

requires you to read this entire Manual before using this machine.

Содержание Hafco Metalmaster S267















Отзывы: