262150
71
Revision A
1035098
A
Figure 4.62: Float Springs
31. Set the header float as follows:
NOTE:
The recommended float setting for cutting on the ground is
when there is approximately 34 kg (75 lb.) weight on each
side of the header at the cutterbar. Readjust as needed for
the given field conditions.
NOTE:
Set the center-link and reel fore-aft to the mid position.
IMPORTANT:
Turn each bolt pair equally.
•
To increase float (decrease header weight), turn both
adjustment bolts (A) clockwise. Repeat the adjustment
at the opposite side of the float module.
•
To decrease float (increase header weight), turn both
adjustment bolts (A) counterclockwise. Repeat the
adjustment at the opposite side of the float module.
1034467
A
A
B
Figure 4.63: Float Spring Locks
32. Lock the adjustment bolts with spring locks (B). Ensure the
bolt heads are engaged in the spring lock cutouts.
33. Tighten bolts (A) to secure the spring locks in place.
DANGER
Ensure that all bystanders have cleared the area.
34. Start the tractor, engage the PTO, and perform the following inspections:
•
Raise and lower the reel to ensure the hoses are properly connected.
•
Engage reel drive on the tractor SCV. Ensure the SCV flow is turned down to prevent overspeeding the reel.
•
Run the header to ensure the hoses are properly connected.
35. Check for hydraulic leaks.
Содержание TM100
