MacDon R116 Скачать руководство пользователя страница 221

Страница: 221 / 234

214713

213

Revision A

11.6.4

Flare-Type Hydraulic Fittings

1003430

Figure 11.17: Hydraulic Fitting

Check flare (A) and flare seat (B) for defects that might
cause leakage.

Align tube (C) with fitting (D) and thread nut (E) onto
fitting without lubrication until contact has been made
between flared surfaces.

Torque fitting nut (E) to specified number of flats from
finger tight (FFFT) or to a given torque value in
Table

11.11, page 213

Use two wrenches to prevent fitting (D) from rotating.
Place one wrench on fitting body (D), and tighten
nut (E) with other wrench to torque shown.

Assess final condition of connection.

Table 11.11 Flare-Type Hydraulic Tube Fittings

SAE Dash Size

Thread Size (in.)

Torque Value

Flats from Finger Tight (FFFT)

lbf·ft

Tube

Swivel Nut or

Hose

-2

5/16

–

—

-3

3/8

–

—

-4

7/16

–

2-1/2

-5

1/2

–

-6

9/16

–

1-1/2

-8

3/4

–

1-1/2

-10

7/8

–

1-1/2

-12

1-1/16

–

113

–

124

–

1-1/2

1-1/4

-14

1-3/16

–

136

–

149

100

–

110

1-1/2

1-1/4

-16

1-5/16

–

160

–

176

118

–

130

1-1/2

-20

1-5/8

–

228

–

250

168

–

184

-24

1-7/8

–

264

–

291

195

–

215

-32

2-1/2

–

359

–

395

265

–

291

-40

–

—

REFERENCE

Torque values shown are based on lubricated connections as in reassembly.

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды