MacDon R1 FR Series Скачать руководство пользователя страница 36

Страница: 36 / 238

262391

Revision A

1010708

Figure 3.7: Driveshield Latch

Insert the flat end of tool (A) into latch (B) and turn it
counterclockwise to unlock the driveshield.

ϭϬϰϯϲϬϴ

Figure 3.8: Left Driveshield

Pull the top of driveshield (A) away from the header
to open it.

NOTE:

For improved access, lift the driveshield off the pins at the
base of the shield, and lay the shield on the header.

3.3.2

Closing Driveshields

Close the driveshields when your maintenance or repair tasks are complete.

WARNING

To reduce the risk of personal injury, do NOT operate the machine without the driveshields in place and secured.

NOTE:

The illustrations shown in this procedure apply to the left driveshield; the right driveshield is similar.

OPERATION

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды