background image

WARRANTY INFORMATION 

This warranty gives you specific legal rights. You may also have other rights which will vary from state 
to state or province to province. 
 

M2

 warrants the 

3-Axis

 Positioner unit against defects in material and workmanship for a 

period of 12 

months 

from date of purchase. During the warranty period, 

M2

 will, at its option, either repair or       

replace products or components which prove to be defective. The warranty shall not apply to defects or 
damage resulting from: 
 

• 

Improper or inadequate maintenance by user 

• 

Improperly prepared installation site 

• 

Unauthorized modifications or misuse 

• 

Accident, abuse, or misapplication 

• 

Normal wear 

 
 

M2

 specifically does not warrant this product for any direct, indirect, consequential, or incidental 

damages arising from the use or inability to use the product. Some states or  provinces do not allow the 
exclusion or limitation of liability for consequential or incidental damages so the above limitation may 
not apply. 
 
 

In the event repair or replacement are necessary, purchaser  shall  contact  M2  for  return         

authorization. In many cases this contact can simplify and expedite the repair / replacement process 
and help reduce costs and downtime. 
 
 

The purchaser shall be responsible for packing the product properly for return and for charges 

to ship the product to 

M2

. Always include with the shipment, a statement detailing the problem / failure 

and any other pertinent observations. Insuring the product for shipment is  recommended. Use the 
original packing materials whenever possible. 

M2 

is responsible for charges 

(in the United States) 

to 

return the repaired / replacement product only where warranty service is involved. 
 
 

M2 Antenna Systems, Inc.  4402 N. Selland Ave. Fresno, CA 93722 

(559) 432-8873 Fax (559) 432-3059 Web: www.m2inc.com 

12 Month Limited Warranty 

Содержание SYSTEM SAMPLE 3

















Отзывы: