background image

12. OVERHEAD BOOM SUPPORT SYSTEM. 
 
Install a temporary mast if possible to get the overhead system just right before installing the antenna. 
 
 

Attach one end of the HPTG-4000 Philistran cable at the eyebolt at the REAR end of the boom. 
Install a thimble or cable eye in the eyebolt. Secure the cable using two 1/4” cable clips. Repeat at 
the other eyebolt.  Attach the turnbuckle plate to the mast about 5 feet above the boom to mast 
plate. Open the 3/8 forged JAW AND EYE turnbuckles till just one thread is showing inside the of 
the turnbuckle. Attach the JAW  end of each turnbuckle at the plate. Insert a thimble or cable eye 
in each turnbuckle eye and then attach the two HPTG-4000 cable, tensioning the cables and 
securing with two more clips on each. Do final boom straightening with the turnbuckles now or at 
the time of installation on the tower. 

 
13. Check ALL hardware for tightness. Check ALL element sections, especially tip sections, for correct 

placement. Make any final adjustments to linear loading tension. 

 
14. Attach feedline section to balun. Route from element #8, back to boom to mast plate. Secure at 

regular intervals with tape or nylon ties. 

 
15. When mounting this log periodic on a tower or mast with other antennas there may be interaction 

with other nearby antennas,  particularly if they are resonant in the 8 to 30 MHz band.  In general 
VHF and/or UHF antennas mounted for HORIZONTAL POLARITY should be at least 40 inches 
above or below the log antenna. Use good quality 50 Ohm feed line to feed the log and be sure 
your tower and rotator system can handle to wind area and weight of this antenna.  

 

THIS COMPLETES ANTENNA ASSEMBLY 

 
 

M

2

 

ANTENNA SYSTEMS, INC.

 

4402 N. SELLAND AVE. 

FRESNO, CA 93722 

(559) 432-8873  FAX: 432-3059 

www.m2inc.com

  Email: 

[email protected]

 

8-30LP9 ASSEMBLY MANUAL 

Содержание 8-30LP9














Отзывы: