background image

19

Premier 4-4-2 Atlantic E-6 Steam Engine

Cab Chatter

Lock-out

Volume

Battery

PSA

Remedy

Remedy

Remedy

Remedy

Remedy

Sometimes the Cab Chatter sounds 
don’t play.

I can’t get the engine to run after I 
power up the transformer. It sits still 
with the engine sounds running.

The engine won’t lock into forward, 
neutral, or reverse.

The sounds seem distorted, especially 
when the whistle or bell is activated.

The engine will not leave the initial 
neutral setting

The PSA sounds occasionally repeat 
themselves.

I get no sounds when the engine shifts 
between directions.

After I turn off my transformer, my 
engine continues to make sounds 
before quitting.

Cab Chatter plays only in neutral.

The engine is locked into the neutral 
position. Follow the procedure in the 
“Lock into a Direction” section.

Engine speed must be below 10 scale 
mph (approx. 10 volts or less in 
conventional mode).

Proto-Sound 2.0 volume is set too 
high. Turn the volume control knob on 
the bottom of the chassis counter-
clockwise to reduce the volume.

Check to be sure the battery is 
installed and fully charged. See the 
“Self-Charging Battery Back-Up” 
section.

The battery may be dead or need to 
be charged. See the “Self-Charging 
Battery Back-Up” section.

Proto-Sound 2.0 is designed to 
continue to sound for a few seconds 
after power to the track has been shut 
off.

Proto-Sound 2.0 has a built-in random 
number generator that randomly 
selects each sound clip to play. 
Because there are a limited number of 
sound clips available in each PSA 
sequence, it is probable that some of 
these sound clips will be repeated 
from time to time.

Содержание PREMIER 4-4-2 ATLANTIC E-6





























Отзывы:

Похожие инструкции для PREMIER 4-4-2 ATLANTIC E-6