M-system Mini-MW Series Скачать руководство пользователя страница 7

Страница: 7 / 8

W2XF

P. / 4

EM-5507

MAINTENANCE

Regular calibration procedure is explained below:

■

CALIBRATION

Warm up the unit for at least 10 minutes.  Apply 0%, 25%,
50%,  75%  and  100%  input  signal.    Check  that  the  output
signal for the respective input signal remains within accu-
racy described in the data sheet.  When the output is out of
tolerance,  recalibrate  the  unit  using  the  PC  Configurator
Software (model: W2CFG).

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for
protection against induced lightning surges. Please contact
M-System to choose appropriate models.

STATUS INDICATOR LED

Combinations of the three front LEDs (LD1, LD2, LD3) indicate the transmitter’s operating status by different flashing pat-
terns.
Examples are shown below.

LD1

LD2

LD3

LD1

LD2

LD3

LD1

LD2

LD3

NORMAL OPERATION (RUN) MODE

ERROR MODE

Parameter Error
Error occurred when reading parameters from the
internal memory.

LD1

LD2

LD3

Overrange Input
The input is below -15% or above +115%.

PC Configuration RUN Mode
The transmitter is configured via PC and
is in normal operating conditions.

AD Conversion Error
Internal AD conversion error.

1. LD1 may be one of the .

LD1

LD2

LD3

Output Limit
The output is at the upper or the lower limit.

Amber LED

Green LED

Red LED

OFF

Blink

Rugghölzli 2
CH - 5453 Busslingen

Tel. +41 (0)56 222 38 18

Fax +41 (0)56 222 10 12

[email protected]

www.sentronic.com

Produkte, Support und Service

SENTRONIC

Содержание Mini-MW Series









Результаты поиска

Содержание Mini-MW Series

Отзывы:

Похожие инструкции для Mini-MW Series

Бренды по названию

Популярные бренды

M-system Mini-MW Series, Быстрый старт

Результаты поиска

Содержание Mini-MW Series

Отзывы:

Похожие инструкции для Mini-MW Series

Бренды по названию

Популярные бренды