M-system 47DM Скачать руководство пользователя | Manualshive

Страница: 87 / 238

background image

87

47DM OPERATING MANUAL EM-9510-B Rev.6

8.1 ALARM OUTPUT PATTERN

The alarm output pattern, normal output (‘NORMAL’) where alarm trips according to the setpoint, or zone output (‘ZONE’)
where alarm trips and resets between each setpoint, can be selected. The default setting is normal output.

IMPORTANT

• Alarm trip action setting is disregarded with zone alarm.
• If a setpoint is set to invalid (‘------’), no output is provided for the zones adjoining the setpoint (e.g. P and L are not

provided with L set to invalid).

HH alarm setpoint

H alarm setpoint

L alarm setpoint (invalid)

LL alarm setpoint

HH alarm output (hi)

H alarm output (hi)

L alarm output (invalid)

LL alarm output (lo)

‘HH’ indicator

‘H’ indicator

‘P’ indicator

‘L’ indicator

‘LL’ indicator

No output for

the zones adjoining

the invalid setpoint

Display value

Display value

HH alarm setpoint

H alarm setpoint

L alarm setpoint (invalid)

LL alarm setpoint

HH alarm output (hi)

H alarm output (hi)

L alarm output (invalid)

LL alarm output (lo)

‘HH’ indicator

‘H’ indicator

‘P’ indicator

‘L’ indicator

‘LL’ indicator

■

TYPICAL ZONE SETTING

■

ZONE SETTING WITH INVALID SETPOINT AT L

«
...
85
86
87
88
89
...
»

Содержание 47DM















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47DM

Бренд: Sanmenxia Страницы: 17

Бренд: SANKO Страницы: 25

Бренд: Samson Страницы: 2

Бренд: Yamaha Страницы: 31

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

Бренд: Energometrika Страницы: 39

Бренд: Aqualytic Страницы: 140

2-WIRE EMM.630CT-MID

Бренд: Qonnex Страницы: 2

VX200-N-VI Series

Бренд: XS Scuba Страницы: 34

Бренд: L.R. Baggs Страницы: 6

Бренд: Princeton Instruments Страницы: 28

Бренд: sewerin Страницы: 80

Бренд: YOKOGAWA Страницы: 63

Бренд: RaySafe Страницы: 2

Бренд: Alma Страницы: 69

Бренд: DeFelsko Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды