DUAL RADIO UNITS
Configure the Dual Radio feature for two remote mount radio units, or one front
mount unit and one remote mount unit. In remote mount configurations, the
control unit is typically located in the vehicle cab, with the radio units located
side-by-side in vehicle trunk. In front mount configurations, the front mount
radio unit is located in the vehicle cab, with the remote mount radio unit located
in a convenient location nearby. The remote mount configuration is the preferred
installation, since a separate control unit is required to program the remote unit in
a front mount configuration.
The following Dual Radio configurations will not work:
•
Any configuration using a DIN cassette mount.
•
Any installation where Extended Options are required from both radio units.
Extended Options are supported in one radio unit only.
STEP 1 - PRE-INSTALLATION PROGRAMMING
All radio units in the Dual Radio configuration
MUST BE PROGRAMMED
PRIOR
to final installation. These configurations provide for a Master radio
unit and a Slave radio unit. In the front mount configuration, the control unit is
mounted to the
master radio unit
. In the remote mount configuration, both radio
units are installed separate from the control unit and the
master radio unit
is
always the radio most directly connected to the control unit. Connect extended
options to the Master radio unit only.
NOTE
Both the Orion Master and Orion Slave mobiles must be
programmed with the same Group version of Flash code. The
Group version must be G30 or later. Failure to do so may
result in inadvertent lockup states in the Dual Radio
configuration.
One radio is programmed as a
master
, and one radio is programmed as a
slave
.
It is recommended that the units be programmed at a Service Center first, and
then transferred to the user's installation. However, some installation and
programming cables are designed to facilitate field programming, see Figure
49 and Figure 50. The radios and control unit must be programmed in a
sequential order to provide each radio with the proper identification code.
Use one of the three programming cables listed on page 4, to program the
Master radio unit and the Slave radio unit as described in the following
sections.
63
Содержание Orion
