4. AC FUSE
Plug the AC power cord into any standard AC outlet. Before plugging this cord in, be sure the voltage of AC outlet is correct.
To protect your device from different kinds of ac problems. If the device is “on” and nothing lights, please verify fuse compartment. If fuse is
broken, please read it and change with a new one of same size and values
5. DMX
INPUT
After you connect the XLR cable on the output of the DMX keyboard, connect the other XLR socket of the cable to this DMX input connector
6. DMX
OUTPUT
Connect this output to the DMX input of another ARTEMIS 3 if you want to control the two ARTEMIS 3 ( or more ) with only one DMX
keyboard. ( the DMX address is used to choose if you want the ARTEMIS 3 devices in the same time or separatly )
7. FAN
Use to refrech the electronic parts and laser. Please, don’t obstruct this area.
.
SAFETY NOTES :
-
The unit is suitable for indoor use only. Protect the unit against humidity and heat (admissible ambient temperature range 10-35°C).
-
The unit heats up during operation. To avoid burnings, do not touch the unit during operation, and after switching off let it cool down
for some minutes before touching it.
-
The heat being generated in the unit has to be carried off via air circulation. Therefore, the vents of the housing must not be covered
with any objects.
-
Do not insert or drop anything into the vents! This could result in electric shock.
-
Do not set the unit into operation, or immediately disconnect the mains plug from the mains socket if:
o
damage can be seen at the power supply unit or mains cable,
o
a defect might have occurred after a drop or simi lar accident,
o
there are malfunctions.
The unit uses lethal mains voltage (230V~). In case of improper action a shock hazard may occur. The unit must in any case be
repaired by authorized, skilled personnel.
-
Adamaged mains cable must only be replaced by the manufacturer or authorized, skilled personnel.
-
Never pull the mains plug out of the mains socket by means of the mains cable.
-
If the unit is used for purposes other than originally intended, if it is mounted or operated in the wrong way or not repaired by
authorized, skilled personnel, there is no liability for possible damage.
-
For cleaning only use a dry, soft cloth. Do not use any chemicals or water.
-
Don’t project the laser beam directly to a person because the beam can cause high damages to eyes.
MOUNTING :
-
Fix the unit via the mounting bracket with a support for light radiating units or a stable mounting screw at the desired place (traverse of
a stand for light radiating units or horizontal bar).
-
For aligning the unit loosen the setscrews at the mounting bracket, adjust the desired inclination of the unit, and tighten the setscrews
again.
Important!To avoid a heat accumulation in the unit, the mounting place must be chosen so that sufficient air circulation is secured during
operation. The vents of the housing must not be covered.
MUSIC OPERATING :
-
Connect the laser unit with the mains plug to a mains socket (220V~240V/50Hz-60Hz).
-
Select the music mode ( AUTO ) on control panel
-
Adjust the desired volume at the music system.
-
If the ARTEMIS 3 don’t move, please increase a little bit the level of the music.
-
For switching off , disconnect the ac cord from the ac main plug.
DMX OPERATING :
-
Connect the ARTEMIS 3 device to the main power supply (220V~240V/ 50Hz-60Hz).
-
Connect the DMX input of ARTEMIS 3 device to the DMX output of the DMX keyboard ( use a XLR-XLR cable )
-
If you want to connect several ARTEMIS 3 devices ( or DMX devices ) in using only one DMX keyboard, connect all the devices as
show in the next drawing
-
In the control panel, select the DMX operating mode ( the display musto indicate 512 with a flashing point )
-
Use your DMX keyboard to control the different channels of the ARTEMIS 3 device(s).
