15
– Loosen the locking screw (4).
– Press the locking lever (5) and hold down.
– Rotate the saw bench (6) stop into the
required position.
The set mitre angle can be read from the
scale (26).
– Release the locking lever (5) again.
– Re-tighten the locking screw (4).
Setting the incline angle
The incline angle can be set steplessly
between 0° to 45°.
– Loosen the locking screw (9).
– Incline the tool arm into the required posi-
tion.
The set angle of inclination can be read from
the scale (27).
– Re-tighten the locking screw (9).
Set the adjustable stop
– Undo the wing nut (3).
– Slide the moving part (2) of the workpiece
stop.
– Tighten the wing nut (3) back up again.
Pulling device
Workpieces with a larger cross-section can
also be sawed using the pulling device. The
pulling device can be used for all cuts
(straight cuts, mitre cuts and double-mitre
cuts).
– When the device is not in use, push the
tool arm back as far as it will go and
tighten the locking screw (17).
Cutting depth limiter
– In combination with the pulling device,
the cutting depth limiter is used for cut-
ting grooves.
– Set the cutting depth using the set-
screw (15).
Cutting line marking
A laser beam indicates the cutting line of the
saw depth. This enables the workpiece to be
precisely positioned prior to being clamped.
– Switch the laser on or off using the
switch (13).
Notes about sawing
• When sawing using the pulling device,
always push the tool arm back (counter
direction).
• The workpiece must be in firm contact
along its entire length. When sawing long
workpieces, always use the table exten-
sion.
• Never saw workpieces set on end, lay
them flat on the saw table and clamp
firmly.
• Secure round workpieces to prevent
twisting.
• Clamp curved (bent) workpieces so that
the side curved outwards is against the
workpiece stop.
Sawing
WARNING! Risk of injury!
Always
tighten the workpiece stop locking
screw before sawing.
WARNING! Risk of injury!
Always
tighten the incline setting locking
screw before sawing.
WARNING! Risk of injury!
Firmly
hold the workpiece only on the right-
hand side for inclined cuts.
Note:
On both sides of the work-
piece stop there must be a gap of
precisely 8 mm to the saw blade.
CAUTION! Risk of injury!
The per-
formance of the laser corresponds to
laser class 2. Never look directly into
the laser.
DANGER! Risk of injury!
The saw
blade is more easily accessible due
to the severe inclination when double
mitre cutting. Maintain an adequate
clearance from the saw blade!
3
2
2
1
GB
temp.book Seite 15 Donnerstag, 7. April 2016 9:58 09
Содержание 380 335
