Lutron Electronics STBO-4SN Скачать руководство пользователя страница 7

Страница: 7 / 8

Troubleshooting Guide

Keypad is working properly when LEDs light up and loads respond as buttons are pressed.

Symptom

Cause and Action

Power is not present at keypad.

• Make sure HomeWorks

Processor is powered up.

• Check for 15 V

between pins 1 & 2 on the keypad connector.

• Remove connector from back of keypad, check connections and replace.

Keypad is properly powered but is not communicating with the processor.

• Verify that the processor is running.

• Check that keypad wires 3 & 4 are properly connected.

• Check that keypad link is plugged into correct connector at processor.

• Verify that link is configured for

HomeWorks

keypads in the

HomeWorks

Software.

Keypad improperly addressed.

• Check keypad for proper address. See Keypad Addressing (page 5).

Keypad improperly programmed.

• Check system programming.

B&O

Beo4

IR Remote is in the incorrect mode.

• Press the “Light” Button before initiating any button presses from the

remote.

Batteries in IR remote are weak

• Replace batteries in remote.

Keypad improperly programmed.

• Refer to Button Function Chart (page 7) and check system programming.

Interference from plasma television.

• Move or turn off plasma television.

LEDs don't light up.

LEDs cycle from top to bottom sequentially.

LEDs light when button is pressed, but the system
response isn't correct.

No response from the keypad when an IR remote button is
pressed.

Содержание STBO-4SN









Результаты поиска

Содержание STBO-4SN

Отзывы:

Похожие инструкции для STBO-4SN

Бренды по названию

Популярные бренды

Lutron Electronics STBO-4SN, Инструкция по эксплуатации

Результаты поиска

Содержание STBO-4SN

Отзывы:

Похожие инструкции для STBO-4SN

Бренды по названию

Популярные бренды