background image

Description

2 conductors / #22-24 AWG

3 conductors (2 shielded, 1 common) 
#24 AWG Belden

®

wire model #1883A

3 conductors:

2 / #18-22 AWG (24 VAC power supply)
1 / #18-22 AWG (earth ground)

6 conductors:

2 / #16 AWG (24 VAC power supply)
1 / #18 AWG (earth ground)
3 #22 AWG sh 1 #24 AWG  

common (comm link)

(

Lutron

wire part no. SV-CBL-MDU-250)

3 conductors #22 AWG 

Lutron

model # SV-IR-EXT-10

Maximum Length

Control to MDU: 250 ft.(76 m)

4000 ft. (1333 m) per system
1000 ft. (333 m) from MDU to MDU

Transformer to MDU:

#18 AWG - 150 ft. (46 m)
#20 AWG - 100 ft. (31 m)
#22 AWG -   60 ft. (18 m)

MDU to 

Sivoia

power panel:

200 ft. (61 m)

50 ft. (15 m) per system - 
total of 5 SV-IR-EXT-10, 10 ft.
(3 m) each

1 2 3 4

5 6 7 8

Cntrl 1

Cntrl 

2

Ground

AC

AC

Common

MUX

MUX

B

Do not connect if there is only one MDU in the system.

If there are

multiple MDU's in the  system,the MDU's must be wired together. Connect the
MUX, Common, and MUX terminals of each MDU together in a daisy chain or
homerun configuration.

To a 

Sivoia

wall mounted keypad, or a 

Sivoia

interface such as the SV-CCI-GRP

or the SV-GRXI. The CNTRL1 and CNTRL2 wires are

polarity sensitive

.

Wire to a 

Sivoia

100VA plug-in transformer, junction box mount transformer,

or a 

Sivoia

power panel. Each MDU must be EARTH grounded. One 

Sivoia

transformer can power

ONLY ONE MDU

regardless of drapery size.

Control

Comm

Link

Power

Supply

IR Connector

System Wiring – Single MDU

6

9

C O N N E C T I N G   W I R E S   T O   T H E   M D U   T E R M I N A L   B L O C K

The terminal block located at the bottom of the MDU is the wire 
connection point for: power, communication, keypads, and interfaces.

1.

Remove terminal block cover by pressing in on the cover and then
pulling downward.

2.

Grasp terminal block and pull down to separate from connecting block.

3.

Connect wires to the terminal block according to the diagram below.

4.

Replace the terminal block and the terminal block cover.

Wire Type

Control

A

Comm Link

B

Power Wires

C

Comm & Power

D

B   &

C   combined 

in one cable

SV-IR 

E

Extension Cable

A

E

B

C

Sivoia

®

Drapery

Содержание SIVOIA

















Отзывы: