Lutron Electronics Energi Savr Node QS QSNE-4S10-D, Руководство по программированию, Страница: 7 / 8

Energi Savr Node
TM
QS | Programming Guide
Energi Savr Node
TM
QS
|
Programming Guide Lutron
®
|
7
QSE-IO Association - Scene DIP configuration
The
Energi Savr Node
QS unit can be associated to a QSE-IO (contact closure interface) that is set in a Scene
DIP configuration. This can be used to change scenes on your Energi Savr Node QS unit from third party
equipment (using contact closure inputs into the QSE-IO), or to monitor scene changes on your Energi Savr
Node QS unit from third party equipment (using contact closure outputs out of the QSE-IO). Consult the QSE-
IO instructions for proper DIP configuration.
To associate a QSE-IO that is set in a Scene DIP configuration to an
Energi Savr Node
QS unit(s), follow the
steps below:
1. Press and hold the Program button on the QSE-IO for 3 seconds to enter Programming Mode. The 5 output
LEDs will cycle. The sensor Group A and Group B LEDs and the ‘H’, ‘M’ and ‘L’ LEDs on the Energi Savr Node
QS unit(s) will flash sequentially in groups.
2. To assign desired zone(s) to the QSE-IO, press and hold the Zone button on the Energi Savr Node QS unit for
each desired zone for 3 seconds. A blinking ‘Zone’ LED indicates an assigned zone.
3. To exit Programming Mode, press and hold the Program button on the QSE-IO for 3 seconds.
To un-assign zones from the QSE-IO, press and hold the Zone button on the
Energi Savr Node
QS unit for 3
seconds. The ‘Zone’ LED will turn off to indicate success.
Repeat for each zone that you wish to un-assign from the QSE-IO.
QSE-IO Association - Zone Toggle and Occupancy DIP configurations
The Energi Savr Node QS unit can also associated to a QSE-IO (contact closure interface) that is set in the
Zone Toggle or Occupancy DIP configuration. In the Zone Toggle configuration, this can be used to toggle
zones on your
Energi Savr Node QS unit from third party equipment (using contact closure inputs into the
QSE-IO), or to monitor the state (on or off) of the zones on your
Energi Savr Node
QS unit from third party
equipment (using contact closure outputs out of the QSE-IO). In the Occupancy configuration, this can be
used to associate additional occupancy sensors to the zones on your
Energi Savr Node QS unit (to turn lights
on and off based on room occupancy). Consult the QSE-IO instructions for proper DIP configuration.
To associate a QSE-IO that is set in a Zone Toggle or Occupancy DIP configuration to an Energi Savr Node QS
unit(s), follow the steps below:
1. Press and hold the
Program
button on the QSE-IO for 3 seconds to enter Programming Mode. The first
output LED will flash indicating input 1 is selected. The sensor Group A and Group B LEDs and the ‘H’, ‘M’
and ‘L’ LEDs on the
Energi Savr Node QS unit(s) will flash sequentially in groups.
2. To assign desired zone(s) to input 1 of the QSE-IO, press and hold the Zone button on the Energi Savr Node
QS unit for each desired zone for 3 seconds. A blinking ‘Zone’ LED indicates an assigned zone.
3. Press and release the Program button on the QSE-IO to select the next input. Repeat step 2 for the remaining
inputs on the QSE-IO.
4. To exit Programming Mode, press and hold the Program button on the QSE-IO for 3 seconds.
To un-assign zones from the QSE-IO inputs, press and hold the Zone button on the Energi Savr Node QS unit
for 3 seconds. The ‘Zone’ LED will turn off to indicate success.
Repeat for each zone that you wish to un-assign from its respective QSE-IO input.