Luminus DK-114N-1 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

Luminus DK-114N-1 Скачать руководство пользователя страница 4

The figures below illustrate the cables included in the DK-114N-1.

Figures 4-7: From left to right: Power supply to driver board cable, Signal cable, Driver board to LED cable, Thermistor cable

Figure 6 depicts two types of driver board to LED cables: the shorter cable (with either 8 - or 10- pins on the LED connector) on the left,

used with LEDs such as PT39, PT40, CBT-40 and PT54, and the longer cable with the two spade connectors on the right, used with LEDs

such as the CBT-90, PT-120 and CBT-120. There are five different variants of the shorter driver board to LED cable : 960011 to be used with

PT39, PT54 and CBT-40; 960043 to be used with PT40-RA; 960044 to be used with PT40-G/B; 960045 to be used with PT54-TE-RA and 960046

to be used with PT54-TE-G/B. These five cables have labels that contain the cable number and the LEDs to which they connect--users must

match the LED they use to the appropriate cable since connecting an incorrect cable can damage the LED. For optimum performance, and

to avoid ringing when pulsing the LEDs, increasing the length of the driver board to LED cable is not recommended.

2.3 Thermal Interface Material (TIM) and Mounting Hardware

The development kit includes precut sheets of eGraf HiTherm 1205, a high performance thermal interface material, and M2x5, M2.5x6

screws required for mounting the LEDs.

Figure 7: TIM sheets

3. User Instructions

The following sections explain the set-up and operation of the DK-114N-1 Development Kit. Additional lab equipment such as a 12 V

laboratory power supply, an oscilloscope, a waveform generator, a multimeter and a photodetector are required to power and use the

DK-114N-1. Table 1 lists a recommended model for the equipment and Appendix D provides an additional list of compatible power

supplies. The use of a table equipped with ESD protection is recommended.

4

960017 Rev C © 2013 Luminus Devices, Inc. - All Rights Reserved

Luminus Devices, Inc.

•

T

978.528.8000 • www.luminus.com

1100 Technology Park Drive • Billerica, MA 01821

DK-114N series - Development Kit Manual

«
...
2
3
4
5
6
...
»

Содержание DK-114N-1













Отзывы:

Нет отзывов