background image

1

960017  Rev C           © 2013 Luminus Devices, Inc. - All Rights Reserved

Luminus Devices, Inc.

   •    

T

 978.528.8000    •    www.luminus.com

1100 Technology Park Drive    •    Billerica, MA 01821 

DK-114N series - Development Kit Manual

Development Kit Manual 

DK-114N-1 and DK-114N-3

Overview

Big Chip LEDs  from Luminus Devices have been designed 
from the ground up to enable a new class of illumination and 
projection systems. Benefiting from a suite of innovations in
chip technology, packaging, and thermal management, Big 
Chip LEDs allow designers to achieve efficient light engine 
designs and deliver high brightness solutions. 

The DK-114N series development kit is a comprehensive so-
lution designed specifically to support the development of 
single and three channel PT and CBT series Big Chip  LEDs. 
Each channel of the kit, comprising of a high current driver, an 
efficient thermal management solution and cables  is capa-
ble of sourcing a drive current of 14 A and ensures that CBT 
and PT series LEDs are operated at up to 70 W for maximum 
brightness. This plug and play solution can easily be connect-
ed to common laboratory equipment through standard con-
nectors and allows system designers to save weeks in their 
development cycles.

Table  of  Contents

1.  Key Features 

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .2

2.  Development Kit Contents 

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .2

 

2.1  Heat Sink and Driver Board  

   .  .  .  .  .  .  .  .  .  .  .  .  .2

 

2.2  Cable Assembly

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3

 

2.3  TIM and Mounting Hardware

   .  .  .  .  .  .  .  .  .  .  .

4

3.   User Instructions 

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

4

 

3.1  Device Mounting Instructions  

   .  .  .  .  .  .  .  .  .  .5

 

3.2  Electrical Connections

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6

 

3.3 Operation

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6

4.  Appendix 

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .9

Содержание DK-114N-1













Отзывы: