LUMINELL SL1 страница 3 Скачать руководство пользователя | Manualshive

Страница: 3 / 72

background image

LUMINELL SWEDEN AB

3

DISCLAIMER

Luminell makes no representations or warranties with respect to this manual and, to the
maximum extent permitted by law, expressly limits its liability for breach of any warranty that
may be implied to the replacement of this manual with another. Furthermore, Luminell
reserves the right to revise this publication at any time without incurring an obligation to notify
any person of the revision.

The information provided in this documentation contains general descriptions and/or
technical characteristics of the performance of the products contained herein. This
documentation is not intended as a substitute for and is not to be used for determining
suitability or reliability of these products for specific user applications. It is the duty of any
such user or integrator to perform the appropriate and complete risk analysis, evaluation and
testing of the products with respect to the relevant specific application or use thereof.
Luminell shall not be responsible or liable for misuse of the information that is contained
herein. If you have any suggestions for improvements or amendments or have found errors
in this publication, please notify us.

All pertinent state, regional, and local safety regulations must be observed when installing
and using this product. For reasons of safety and to ensure compliance with documented
system data, only the manufacturer or any of their registered service partner shall perform
repairs on this product.

Failure to observe this information can result in injury or equipment damage.

Copyright © 2021 by Luminell.

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted
in any form or by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior written permission of the publisher.

For permission requests, contact us at the address:

[email protected]

«
1
2
3
4
5
...
»

Содержание SL1









































































Отзывы:

Нет отзывов

Похожие инструкции для SL1

Crouse-Hinds FMV Series

Бренд: Eaton Страницы: 3

Бренд: Francis Searchlights Страницы: 32

Бренд: B-K lighting Страницы: 2

Бренд: Ibiza Страницы: 9

Outdoor Surface RD 13W/3000K GY IP54

Бренд: Ledvance Страницы: 4

Бренд: Xtricity Страницы: 4

Бренд: RTRMAX Страницы: 21

EPLC2-LED-150W-RT-JB2-50C

Бренд: Larson Electronics Страницы: 3

Бренд: COMMAND TOOLS Страницы: 2

UVG Medical Torch

Бренд: Labino Страницы: 12

Бренд: HQ Power Страницы: 35

Бренд: Stahl Страницы: 28

Бренд: Defiant Страницы: 2

XLamp ML Series

Бренд: Cree Страницы: 12

Бренд: ProLights Страницы: 44

Бренд: Makita Страницы: 168

Бренд: Makita Страницы: 40

Бренд: Makita Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды