• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
MOUNTING
Each CRMX Nova unit is supplied with a M10 T-screw and nut
to allow the unit to be securely fixed to any mounting point,
such as trussing.
Release 4.0 June 2016
SPECIFICATIONS
Power protection:
Overvoltage and ESD protected power input
Operation temp. range: -20°C to +40°C (-4°F to 122°F) (ambient)
Environmental:
For indoor use only
Frequency range:
2.402 to 2.480 GHz
Output power levels:
300mW (25dBm) (Permitted only in North
America), 100mW (20dBm), 35mW (15dBm),
10mW (10dBm)
PoE operation:
IECTR 62101. The PoE port is to be connected
only to PoE networks without routing to the
outside plant
Low voltage operation:
This product can also be powered by a UL listed
LPS power supply rated 12VDC, maximum 1A
CRMX™, CRMX Nova™, CRMX Outdoor™, CRMX Slim™, CRMX OEM™, CRMX SuperNova™ are trademarks of LumenRadio AB. W-DMX™ is a trademark of Wireless Solution
Sweden AB. CRMX is patent pending, CE, FCC, ICES, SRRC and ARIB STD-T66 approved.
Panel
Power req.
Power req.
label 100 - 240VAC* 12VDC ± 20%
TX
5W
7W
5W 5W
10W
16W
RDM
RX
5W
5W
RDM
FX
5W
8W
2
3
1
SECURITY WIRE:
All CRMX Nova units have slots where a security wire can be attached.
See illustration.
FCC ID: XRSCRMXNOVA101
IC: 8879A-CRMXN101
US Patent 7,432,803
All CRMX units are upgradeable. Please contact your local
distributor for more information.
TO USE A T-SCREW
1. Lower the T-screw into the slot on the side of the unit and
then twist it clockwise to lock.
2. Place the nut onto the screw.
3. Turn the nut clockwise until it tightens across the slot, thus
locking the T-screw securely within the slot.
4. You can now attach the unit to a secure mounting point.
EU Declaration of Conformity
These products comply with the RED (Radio Equipment
Directive) of the European Union (2014/53/EC). This
equipment meets the following conformance standards:
ETSI EN 301 489-1 V1.8.1; ETSI EN 301 489-3 V1.4.1;
ETSI EN 300 328 V1.81; EN 609 50
FCC statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
lumen
radio
Connectivity for a Better World
R
001 - A
00019
RX
RDM
TX2
RDM
TX2
The TX2 units include a replaceable
fuse. This should be replaced with a
1A, 250VAC time-delay fuse.
FIRMWARE UPGRADE
SPECIFICATIONS - MODEL DEPENDENT
For any questions, please contact
[email protected] or call
+46 (0)31 301 03 70.
+46 31 301 03 70
|
|
www.lumenradio.com