Lumag EB400PRO Скачать руководство пользователя

Страница: 8 / 48

reservations

Information on specifications, dimensions and illustrations of the machine as well as changes of

safety standards are subject to further development and are therefore not in any case for the

supply binding.

Printing and typographical errors.

INFORMATION MANUAL

This manual describes functions, operation, maintenance and care of your new machine. Please

read it carefully and follow the instructions carefully to ensure your machine a long life and give

you a safe operation. Observe the safety information and instructions as well as for the local

accident prevention regulations and general safety regulations.

Read Before carrying out any work with the machine, the operating manual, especially the

section on safety and the respective safety instructions. You must fully understand the read and

observe. These are basic instructions and suggestions to prevent accidents. Errors in operation,

inspection and maintenance can cause injury or even death.

INTENDED USE

This comfortable one-man drill is exclusively intended for drilling holes in the ground up to 250

mm diameter. The machine finds its wide range of applications, such as in the garden

maintenance. B. for excavating planting holes, for making holes for fence posts or pergolas on

light soils and well accessible documents.

There are drills of 150 mm, 200 mm and 250 mm diameter for this model.

The machine may be used only in the vertical position (drill down) and must be held during

operation with both hands.

INFORMATION ON THE OPERATING

INSTRUCTIONS INTENDED USE

Содержание EB400PRO

















































Результаты поиска

Содержание EB400PRO

Отзывы:

Похожие инструкции для EB400PRO

Бренды по названию

Популярные бренды

Lumag EB400PRO, Руководство оператора

Результаты поиска

Содержание EB400PRO

Отзывы:

Похожие инструкции для EB400PRO

Бренды по названию

Популярные бренды