Lumag CNCJ-72FW Скачать руководство пользователя

Страница: 25 / 25

CNCJ-72FW CNCJ-80K –

TROUBLESHOOTING GUIDE

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

Operation not satisfactory

Rotational speed

fluctuates.

Governor adjustment

improper?

Adjust governor to correct lever.

Governor spring defective?

Clean or replace ignition.

Fuel flow erratic?

Check fuel line.

Air taken in through suction

line?

Check suction line.

Recoil starter not

working properly.

Dust in rotating part?

Clean recoil starter assembly.

Spiral spring failure?

Replace spiral spring.

Engine rotates but

amplitude not uniform

or does not strike.

Operation speed of throttle

lever is incorrectly set?

Set throttle lever to correct position.

Oil in excess?

Drain excess oil. Bring to correct level.

Clutch slips?

Replace or adjust clutch.

Spring Failure?

Replace spiral spring.

Speed of engine improper?

Adjust engine speed to correct operating

RPM setting.

Содержание CNCJ-72FW


























Результаты поиска

Содержание CNCJ-72FW

Отзывы:

Похожие инструкции для CNCJ-72FW

Бренды по названию

Популярные бренды

Lumag CNCJ-72FW, Руководство оператора

Результаты поиска

Содержание CNCJ-72FW

Отзывы:

Похожие инструкции для CNCJ-72FW

Бренды по названию

Популярные бренды