background image

IMPORTANT!  
 
Always reduce the RF Output power to minimum before changing 
the transmission frequency. Once the new frequency is active, 
slowly increase the RF output power control to provide the 
required power output level. 

 

 

 

WARNING!  
 
Never operate this device without a suitable 50 ohm load 
connected to the RF OUTPUT socket, or without a suitably 
installed and matched antenna system connected. Although the 
output of this transmitter is protected against antenna load 
faults, MIS-OPERATION MAY RESULT IN DAMAGE NOT COVERED 
BY ANY WARRANTY. 

 

IMPORTANT!  
 
Correct operation of the cooling fans in this product is vital to 
reliable continuous operation. Schedule bi-annual maintenance 
checks. We strongly advise the use of a standby transmitter 
system for use during maintenance events or fault conditions, to 
prevent prolonged breaks in transmission. 

 

IMPORTANT!  
 
When cycling the power off, then on, ensure that the transmitter 
is off for at least 10 seconds before re-applying power, to allow 
the internal circuits time to fully reset. Failure to do so may result 
in no RF output (PLL failsafe mode). 
 
Consideration should be given to fitting a suitably rated UPS if 
power interruptions are likely. Similarly, telemetry reset of power 
may be advisable for transmitters in remote areas, or having 
restricted access arrangements. 

 

Содержание FMTX100M














Отзывы: