Lucent Technologies PacketStar PSAX 45N74 Скачать руководство пользователя страница 56

Страница: 56 / 104

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the Ports

3-20

255-700-585

PacketStar

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

The ATM UNI Interface Configuration window is displayed. See the

PacketStar

PSAX Connections Provisioning Guide

for instructions on config-

uring the ATM UNI interface.

Repeat steps 5–8 for the second and third ports, as needed.

Note:

To manage the interfaces, use the commands in the Protection
3-Port DS3 ATM Configuration window (see Figure 3-8) and the
Protection 3-Port DS3 ATM Port and Channel Configuration win-
dow (see Figure 3-9) as needed.

End

Configuring the Ports in E3 Mode

To configure the module for the E3 mode, perform the following procedure.

Begin

Configuring the Ports (E3 Mode)

On the Console Interface Main Menu window (see Figure 3-10), select
the Equipment Configuration option.

The Equipment Configuration window (see Figure 3-11) is displayed.

Figure 3-10. Console Interface Main Menu (Equipment Configuration Selected)

Содержание PacketStar PSAX 45N74








































































































Результаты поиска

Содержание PacketStar PSAX 45N74

Отзывы:

Похожие инструкции для PacketStar PSAX 45N74

Бренды по названию

Популярные бренды

Lucent Technologies PacketStar PSAX 45N74, Руководство пользователя

Результаты поиска

Содержание PacketStar PSAX 45N74

Отзывы:

Похожие инструкции для PacketStar PSAX 45N74

Бренды по названию

Популярные бренды