Lucent Technologies Network Access Module Скачать руководство пользователя

Страница: 20 / 75

Installation and Configuration Steps

1-4

INA Module Installation and Configuration Guide

Ethernet Port. This RJ-45 connector provides a 10BaseT Ethernet connection. See
“Connect an Ethernet Cable” on page 3-4.

Ethernet Link LED. This green LED indicates link integrity to a 10BaseT hub. See
“Ethernet LEDs” on page 3-6.

Reboot Button. This button resets the router hardware and reboots ComOS. It has no
effect on MERLIN MAGIX voice operation. You will need a thin object such as a
straightened paper click to activate this recessed switch.

T1/PRI Connection. This RJ-45 connector connects the T1/PRI line. See “Connect a
T1/PRI Cable” on page 3-3.

DS-1 Test Jacks. There are three pairs of jacks for DS-1 troubleshooting. See “Using
the DS-1 Test Jacks” on page A-5.

Installation and Configuration Steps

Collect information about your T1 or PRI line.

See “T1/PRI Provisioning” on page 2-1 for a preview of the values you need.

Collect information about the network and routing configuration.

See “Network Settings” on page 2-2 for a preview of the values you need.

Install the INA module in the MERLIN MAGIX system.

See “Install the INA Module in a Carrier” on page 3-1.

Configure the T1 or PRI line using the MERLIN MAGIX console.

See “Set Up T1/PRI on the MERLIN MAGIX” on page 2-1.

Assign data channels to the router using the MERLIN MAGIX console.

See “Assign T1/PRI Channels” on page 2-2.

Connect the INA module front panel cables.

See “Connect Cables” on page 3-1.

Configure the INA module.

See one of the following:

–

“Using the INAWizard” on page 4-1.

–

“Using the Command Line Interface” on page 5-1.

–

“Using PMVision” on page 6-1.

Содержание Network Access Module












































































Результаты поиска

Содержание Network Access Module

Отзывы:

Похожие инструкции для Network Access Module

Бренды по названию

Популярные бренды

Lucent Technologies Network Access Module, Руководство по установке и настройке

Результаты поиска

Содержание Network Access Module

Отзывы:

Похожие инструкции для Network Access Module

Бренды по названию

Популярные бренды