LOYTEC CEA-709 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 43

LOYTEC CEA-709 Скачать руководство пользователя страница 29

L-Switch User Manual

29

LOYTEC

Version 6.0

LOYTEC electronics GmbH

System Configuration Menu
=========================

[1] Configure date/time : Mon Sep 10 09:34:29 2012 (UTC+00:00)
[2] Configure earth pos : 48:13:14 N 16:20:05 E 200 m
[3] Remote configuration: disabled

[q] Quit without saving
[x] Exit and save

Please choose:

Figure 18: System Configuration Menu

1 – Configure date/time

This menu option allows setting the battery powered on-board real-time clock.

2 - Configure earth pos

This menu option allows configuring the longitude, latitude and elevation of the device.

3- Remote configuration

This menu option allows enabling/disabling the remote configuration functionality of the
device (e.g. by the LOYTEC L-WEB system).

5.3.4 CEA-709 Configuration Menu

This menu allows changing the CEA-709 transceiver configuration, enabling the collision-
less backbone mode for TP-1250 transceivers, enabling bit-rate auto-detection for RS-485
transceivers, and configuring the CEA-709 router mode.

CEA-709 Configuration Menu
==========================

[1] Port 1 : XF/TP-1250 (1250 kBit)
Port 2 : FT
Port 3 : FT
Port 4 : FT
Port 5 : FT

[r] Router configuration : Configured Router (DIP)

[q] Quit without saving
[x] Exit and save

Please choose:

Figure 19 CEA-709 configuration menu.

1 to 5 - Change transceiver configuration for Port 1 – 5

This menu item allows setting the default transceiver configuration for port 1 to 5 if there
are different possible transceiver configurations.

For TP-1250 transceivers it is possible to set the transceiver settings to collision-less
backbone mode. Please contact LOYTEC if you think you might need this feature!

For RS-485 transceivers it is possible to manually set the bit-rate or choose bit-rate auto-
detection. If auto-detection is enabled the detected bit-rate is shown. See Section 4.2 for an
in-depth discussion of this feature.

9 - Bit-rate auto-detection configuration source (only if RS-485 port is present)

This menu item allows to set what decision element should be used to enable or disable the
bit-rate auto-detection. If [1] DIP Switch is selected the value set on the DIP switch (see

«
...
27
28
29
30
31
...
»

Содержание CEA-709












































Отзывы:

Нет отзывов