Lowrance X510C Скачать руководство пользователя

Страница: 106 / 128

100

If, for example, you execute the Restore Defaults command from your

Port Fuel Flow Advanced Options menu, only the settings for the Port

Fuel Flow will be reset to factory defaults. Other fuel flows on the net-

work will not be affected.

To restore default settings:

1. Press

MENU| MENU

, use

↑

↓

to select

NMEA

2000

and press

ENT

. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.
2. Highlight

ETUP

and press

ENT

, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.
3. Use

↑

↓

to select the desired fuel flow and press

ENT

. The Device

Configuration menu will appear.
4. Highlight

DVANCED

PTIONS

and press

ENT

5. Select

ESTORE

EFAULTS

and press

ENT

. The following message will

appear:

Are you sure you wish to change this device's configuration?

6. Highlight

and press

ENT

. Press

EXIT

repeatedly to get back to the

main display.

EP-15 Fluid Level Configuration

To input Device Name:

1. Press

MENU| MENU

, use

↑

↓

to select

NMEA

2000

and press

ENT

. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.
2. Highlight

ETUP

and press

ENT

, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.
3. Select a fluid level you want to rename and press

ENT

. The Device

Configuration menu will appear with the Device Name dialog box high-

lighted.
4. Press

ENT

and use

↑

↓

←

→

to input the desired name for the fluid

level. Press

ENTER

. Press

EXIT

repeatedly to get back to the main dis-

play.

To select Tank Instance (Location):

1. Press

MENU| MENU

, use

↑

↓

to select

NMEA

2000

and press

ENT

. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.
2. Highlight

ETUP

and press

ENT

, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

www.Busse-Yachtshop.de email: [email protected]

Содержание X510C

































































































































Результаты поиска

Содержание X510C

Отзывы:

Похожие инструкции для X510C

Бренды по названию

Популярные бренды

Lowrance X510C, Руководство по эксплуатации

Результаты поиска

Содержание X510C

Отзывы:

Похожие инструкции для X510C

Бренды по названию

Популярные бренды