Lowrance X510C Скачать руководство пользователя страница 87

Страница: 87 / 128

Radar

When you access the Radar Page, the screen will switch to the radar dis-

play. Information on radar installation and radar operation are included
in two documents that come packed with Lowrance radar units:

Radar

and RIM 100 Radar Interface Module Installation Instructions

and

Radar

Operation Instruction Manual

. Refer to these documents for information

on your radar unit.

NOTE:

Before using your radar, make sure you have checked the Enable

Radar Port checkbox on the main menu.

To enable Radar Port:

1. From a sonar page, press

MENU

to access the main menu.

2. Highlight

NABLE

ADAR

ORT

and press

ENT

, which will place an

the Enable Radar Port checkbox.
3. Repeat Step 2 to disable the radar port, which will uncheck the

checkbox. Press

EXIT

to return to the sonar display.

To access Radar Page:

1. Press

PAGES

, highlight the

ADAR

tab and press

ENT

2. Press

MENU

to open the Radar menu. Press

EXIT

to return to the ra-

dar display.

Radar Page (left) with Radar menu display (right).

Sonar Simulator

This unit has a built-in simulator that lets you run it as if you were on

the water. All sonar features and functions are useable. When in simu-

lator mode, you will see [Simulated] at the bottom of the display.

www.Busse-Yachtshop.de email: [email protected]

Содержание X510C

































































































































Результаты поиска

Содержание X510C

Отзывы:

Похожие инструкции для X510C

Бренды по названию

Популярные бренды

Lowrance X510C, Руководство по эксплуатации

Результаты поиска

Содержание X510C

Отзывы:

Похожие инструкции для X510C

Бренды по названию

Популярные бренды