Lotos Technology LTP5500D Скачать руководство пользователя страница 27

Страница: 27 / 31

/ 28

❖

CAUSES OF COMMON HAND-CUTTING ISSUES

The work piece is not cut completely through. This can be caused by:

⚫

The amperage setting is too low for the thickness of the work piece.

⚫

The cutting speed is too fast.

⚫

The consumables are too worn.

⚫

The amperage setting is set too low for the thickness of the work piece.

⚫

Gouging consumables are installed instead of cutting consumables.

⚫

The work clamp is not attached properly to the work piece.

⚫

The air pressure is too low, or the air flow rate is not high enough.

Cut quality is poor. This can be caused by:

⚫

The amperage setting is too low for the thickness of the work piece.

⚫

Your cutting speed is too quick or too slow.

Consumables’ life is shorter than expected. This can be caused by:

⚫

Moisture in the air supply.

⚫

Incorrect air pressure.

⚫

Consumables are incorrectly installed.

Содержание LTP5500D
































Результаты поиска

Содержание LTP5500D

Отзывы:

Бренды по названию

Популярные бренды

Lotos Technology LTP5500D, Руководство пользователя

Результаты поиска

Содержание LTP5500D

Отзывы:

Бренды по названию

Популярные бренды