manualshive.com logo in svg

Lotos Technology LTP5500D, Руководство пользователя

Поделиться
Скачать
Lotos Technology LTP5500D Скачать руководство пользователя страница 12

 

9

  / 28 

 

The unit is connected to the supply even if the Power S

witch is in the “OFF” 

position meaning there are electrically live parts inside the power source as 
long as it is plugged in. Carefully follow the instructions given in this manual. 

❖

 

PANEL EXPLANATION

 

 
 
 
 
 
 
 
 

1 

 

Torch protection indicator, it illuminates when the consumable parts of the machine 
are not well installed, or the torch head is shorted. Meanwhile the 
Machine stops working. 

2 

 

Power indicator, it illuminates when the machine is powered on 
And it flashes after arc is successfully ignited. 

3 

 

Overheating indicator, it illuminates when the working temperature of the 
IGBT is overly high. Meanwhile, the machine stops working. 

4 

   

Air-check indicator, it illuminates when 
the machine is under air check status. 
At this moment, the machine cannot cut 
 

 

Normal cutting mode, the machine 
can cut when this indicator 
illuminates. 

5 

 

2T indicator torch switch when the 
machine is under 2T status. 

With the 2T option selected, press the trigger to 

fire the torch. You need to hold the trigger while 

continuing to cut. Release the trigger to stop the 

arc.

 

 
 

4T indicator torch switch when the 
machine is under 4T status. 

With the 4T option selected, press the 

trigger to fire the torch. You can then 

release the trigger while continuing to cut. 

Press the trigger again to stop the arc. The 

arc also stops if you lose transfer.

 

6 

LED Current Display 

7 

Amperage Control Knob 

8 

Air Pressure Gauge 

9 

Output Connector (DC+) 

10 

Plasma Torch Connection (DC-) 

11 

Air Regulator 

12 

ON/OFF Power Switch 

13 

Air Supply Connector 

14 

Power Input Cable 

 

 

Содержание LTP5500D
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды