Loopcomm LP-8696C Скачать руководство пользователя

Страница: 14 / 75

WLAN Broadband Router

User Manual

- 14 -

4.3.2

Operation Mode

This page is used to configure which mode wireless broadband router acts.

Item

Description

Gateway

Traditional gateway configuration. It always connects internet via ADSL/Cable
Modem. LAN interface, WAN interface, Wireless interface, NAT and Firewall
modules are applied to this mode

Bridge

Each interface (LAN, WAN and Wireless) regards as bridge. NAT, Firewall and
all router's functions are not supported

Wireless ISP

Switch Wireless interface to WAN port and all Ethernet ports in bridge mode.
Wireless interface can do all router's functions

Apply Changes

Click the

Apply Changes

button to complete the new configuration setting.

Reset

Click the

Reset

button to abort change and recover the previous configuration

setting.

Содержание LP-8696C












































































Результаты поиска

Содержание LP-8696C

Отзывы:

Похожие инструкции для LP-8696C

Бренды по названию

Популярные бренды

Loopcomm LP-8696C, Руководство пользователя

Результаты поиска

Содержание LP-8696C

Отзывы:

Похожие инструкции для LP-8696C

Бренды по названию

Популярные бренды