Look 795 BLADE RS 2019 Скачать руководство пользователя страница 16

Страница: 16 / 22

To disassemble or adjust your AEROPOST 2, unscrew the clamp so that you can slide your seat post without
damaging it, then adjust the position or remove the seat post to disassemble it.

1 / Take a 2 mm Allen key and insert it into the hole
located in the saddle tube (Fig. 19)

= Allen key is in contact with the seat post.

You have met the minimum insertion requirement

NOK

= The Allen key is going into the tube and is not

in contact with the seat post. You have not met the
minimum insertion requirement

Fig. 19

Check the seat post is inserted the minimum amount

Loosening / Position adjustment

AEROPOST 2 SEAT POST

IMPORTANT:

Take care to ensure the minimum insertion of the seat post in the frame, do this as follows.

NOTE :

If there is any noise when

tightening or loosening, you should
grease it again.

With your 795 BLADE RS you will find a factory assembled expander developed specifically for the 795
BLADE RS pivot.

Fig. 17

Rear flange

Front flange

Fixing screw – HEX 4 mm Allen -

10 Nm + grease

O ring

Washer

Graissez les surfaces

Put some grease

Dégraissez les surface de friction

Degrease the friction surface

Modification

Treatment

Date

SHEET A3

SCALE 2:1

Material

ATS-009

000 20926

P.BIGARD

Ind.

Date

Resp

REFERENCE

PART

Cheked by

Date

Drawn by

ASSEMBLY

000 20926

GENERAL TOLERANCES :

Dimension from 0 to 15 : ±0.15

Dimension from 15 to 30 : ±0.20

Beyond : ±0.25

Angles : ±30'

Surfaces finish : 80 grit sand blast

Free of positive metal, voids and porosity

Free of cutting oil and oil residue

000 20926 - Assemby -

Aeropost2_Clamp

01/01/1601

01/01/1601

Volume (mm3)

Mass (g)

17.36

5084.09

01/01/1601

Modification

Treatment

Date

SHEET A3

SCALE 1:3

Material

Ind.

Date

Resp

REFERENCE

PART

Cheked by

Date

Drawn by

ASSEMBLY

GENERAL TOLERANCES :

Dimension from 0 to 15 : ±0.15

Dimension from 15 to 30 : ±0.20

Beyond : ±0.25

Angles : ±30'

Surfaces finish : 80 grit sand blast

Free of positive metal, voids and porosity

Free of cutting oil and oil residue

01/01/1601

01/01/1601

Volume (mm3)

Mass (g)

01/01/1601

Содержание 795 BLADE RS 2019























Результаты поиска

Содержание 795 BLADE RS 2019

Отзывы:

Бренды по названию

Популярные бренды

Look 795 BLADE RS 2019, Руководство пользователя

Результаты поиска

Содержание 795 BLADE RS 2019

Отзывы:

Бренды по названию

Популярные бренды