London Electronics INTUITIVE-L Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

London Electronics INTUITIVE-L Скачать руководство пользователя страница 7

Page 4

Getting Started

First, please check that the display will suit all the requirements of your
application. Page 4 has some important warnings - please check that all warnings
are covered.

If you have analogue output or alarm relay options, you may need to configure
their boards before installing the meter in a panel. See the separate sections in
this manual for those options.

Check that your panel cutout is correct , 92mm wide, 45mm high. You must fit the
meter in a protective enclosure for installation class II service. Remove the 2
screws holding the U clamp at the rear of the case. Slide the meter into the cutout
and re-fit the U clamp and screws. Tighten the screws just enough to hold the
meter firmly in place and make sure the sealing gasket is evenly held between
the panel and the bezel.

Connect the signal and power cables, to the appropriate screw terminal connectors.
Check that you are using the correct terminals or you may cause damage to the
meter. Do not connect any output or alarm cabling yet.

Apply power, and confirm that the meter illuminates all segments for a few
seconds and then shows the software version “I-L X.X” briefly (The X numerals
depend on version).

The calibration lockout switch should be OFF to allow you to change the meter’s
settings. Set the scaling to suit your system, using one of the scaling methods
described in this manual. Check that the meter responds correctly. Now, adjust
your analogue output settings, if necessary, and alarm settings. Use a DVM of
sufficient precision to check that the analogue output is operating as required,
and use a continuity tester to check that the relay contacts operate correctly.
Switch the meter off, and check alarm relay contact status. The alarm lockout
switch should be OFF to allow you to change the meter’s alarm settings.Check
that the contact status suits your system, in conditions of power loss to the meter.

When you have checked all settings, you can connect the alarm relay and analogue
output cables, to check correct system operation

Remember to set the lockout switches ON when you have finished , to prevent
accidental loss of your settings.

«
...
5
6
7
8
9
...
»

Содержание INTUITIVE-L

































Отзывы:

Нет отзывов