London Electronics Fusion-L 6 digit Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 44

background image

42

Equipment Specifications

Case Material

Heavy duty welded uPVC

Connectors

Internal detachable Screw Terminal connectors accessed via
compression glands

Environmental

Storage Temperature range -20 to +70C, non condensing.
Allow 30 minutes for display to reach thermal equilibrium.
Operating temperature range 0 to 50C. Internal heater option
available for use in conditions down to -25C

Power

100-240 VAC, 48 VAC, 45 to 60Hz or 11-30 VDC optional

Burden

40VA maximum

Sealing

IP65 all round, provided the display is mounted vertically and that all
cable glands and rear case-closure screws are properly secured.

Input Signals (bipolar)

4 or 6 wire loadcell up to +/-40mV (+/- 100mV option)

Input Resistance

>10 Megohms

Accuracy

+/-0.05% of range

Span tempco

25 ppm/Degree Celsius

Zero Tempco

30 ppm/Degree Celsius

5V Excitation voltage

5VDC nominal rated at 40mA. Must connect to Sense.

10V Excitation voltage

10VDC nominal rated at 120mA. Must connect to Sense.

Excitation Sense

Ratiometric, 4V absolute minimum allowed after line drops

Filtering

/ smoothing

Selectable time constants of 0 to 25 seconds.

A/D conversion

Sigma-Delta 10 conversions per second, 50/60Hz rejection
Resolution 1 in 400 000 max. over full range

Display update rate

10 readings per second.

Display Range (max)

-199999 to +199999, depending on available signal level.

Plug-In Output Options

Analogue, Alarm, Serial, Clock

See separate manuals available from our website

Record of Revisions

17 November 2010

Version  F00.19  Software  released.  Intended  for  use  with  9122-2470  input  board,
having switched  capacitor  input  filter  feature.
The  newly  released    9122-2470  input  board  allows  selection  of  5V  or  10V  excitation.

5 January 2011

Version F00.20 Software released. Allows serial data output to derived fron Net or
Gross measurement.

14 February 2011

Version F00.21 Software released. Added permanent segment test mode in bootup
routine options. W arranty increased, terms added.

22 August 2011

Corrected Remote programmer connector details.

Default Input configuration switches

Link S8, S9, S10, S11. Open S2, S3, S4, S12, S13

Excitation voltages

5V DC

Link S11. Open S7 and S12 and S13

10V DC

Link S11 and S7. Open S12 and S13

Excitation Ratiometry

Ratiometric. Link S6. Open S1 (default)
Non ratiometric. Link S1. Open S6

9122-2470

S11 S7

S12 S13

Input Conditioner Board

S2
S8
S3
S9
S10
S4

S6 S1

S5

«
...
40
41
42
43
44
»

Содержание Fusion-L 6 digit













































Отзывы:

Нет отзывов

Похожие инструкции для Fusion-L 6 digit

Бренд: Oakton Страницы: 69

Бренд: Trebs Страницы: 44

Greenlee CLM-1000

Бренд: Textron Страницы: 36

Бренд: Ntron Страницы: 29

ACCURE 2350-GAS

Бренд: ROOTECH Страницы: 26

Бренд: THORLABS Страницы: 49

Бренд: Velleman-Kit Страницы: 9

Бренд: Isspro Страницы: 2

Бренд: LaMotte Страницы: 2

Бренд: YOKOGAWA Страницы: 104

Rainbow RTI-Nano Series

Бренд: Laserworld Страницы: 25

BIP LD2-T017-01-EP-S4 Series

Бренд: Balluff Страницы: 16

Бренд: janitza Страницы: 96

Бренд: Groz Страницы: 12

Бренд: Anritsu Страницы: 127

Бренд: Lisle Страницы: 8

Бренд: Castle group Страницы: 2

Бренд: Elcometer Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды