London Electronics Fusion-L 6 digit Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 44

background image

2

..

Warranty

We warrant our products against defects in materials or workmanship for a period of three
(3) years from the date of purchase.

In the event of a defect during the warranty period, the unit should be returned, freight (and
all duties and taxes) prepaid by the Buyer to the authorised distributor from where the unit
was purchased.

The Distributor, at its option, will repair or replace the defective unit. The unit
will be returned to the Buyer with freight charges prepaid by the distributor.

LIMITATION OF WARRANTY
The foregoing warranty shall not apply to defects resulting from:

1. Improper or inadequate maintenance by the buyer.
2. Unauthorised modification or misuse.
3. Operation outside the environmental specification of the product.
4. Mishandling or abuse.

The warranty set forth above is exclusive and no other warranty, whether written or oral is
expressed or implied. We specifically disclaim the implied warranties of merchantability
and fitness for a particular purpose.

EXCLUSIVE REMEDIES
The remedies provided herein are the buyer’s sole and exclusive remedies.

In no event shall we be liable for direct, indirect, incidental or consequential damages
(including loss of profits) whether based on contract, tort or any other legal theory.

«
1
2
3
4
...
»

Содержание Fusion-L 6 digit













































Отзывы:

Нет отзывов

Похожие инструкции для Fusion-L 6 digit

Бренд: QLA Страницы: 18

Бренд: Bacharach Страницы: 60

Бренд: Bacharach Страницы: 4

Бренд: Bacharach Страницы: 17

Бренд: Callaway Страницы: 11

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды