London Electronics Fusion-L 6 digit Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 44

background image

40

RS232, RS422
RS485
plug-in option

Analogue
output
plug-in option

Al arm relays.
Depending on
the option, there
will be none, 2 or
4 relays fitted.

Main option board

Main board

How to install option boards

Where the product is intended for “UL” installations
removal or addition of option boards is not permitted.

!

Warning:

Disconnect

power before you expose
the internals of the display

If you want to open your display to install or modify option boards, follow these steps...

1)

Switch off power to the display and unplug all connectors.

2)

Undo all the thumb screws on the rear case, store them safely and remove the back
panel

3)

Locate the main option board, which will be similar in appearance to the diagram below.
If a main option board is absent, which will be the case if the display was ordered without
any output options, then a main option board will need to be fitted.

The board assemblies will look like this...

The analogue output and RS232 or RS422 plug-in option boards are fixed to the main option
board with white plastic pillars. You must apply a firm force when fitting or removing these
options.

Always be careful to connect the pins to sockets accurately. When reassembling, make sure
option boards are firmly fixed to the upper option board.

Real Time
Clock option

Input board

«
...
38
39
40
41
42
...
»

Содержание Fusion-L 6 digit













































Отзывы:

Нет отзывов

Похожие инструкции для Fusion-L 6 digit

LevelMaster 7100

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 4

Бренд: PAT Страницы: 55

Бренд: PAT Страницы: 31

Бренд: Oldham Страницы: 43

Бренд: Nagano Keiki Страницы: 25

Бренд: Palstar Страницы: 15

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

Бренд: Fora Страницы: 64

Panametrics XDP

Бренд: Baker Hughes Страницы: 64

Бренд: IROX Страницы: 8

AS-i CompactModule M8

Бренд: IFM Страницы: 4

Бренд: THE ELECTRON MACHINE CORPORATION Страницы: 32

Бренд: Vector Страницы: 8

FI-500 FiberInspector Micro

Бренд: Fluke Страницы: 2

Бренд: Gatekeeper Страницы: 2

Бренд: Midtronics Страницы: 58

Бренд: R&S Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды