LONCIN WG6500M-1 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 31

LONCIN WG6500M-1 Скачать руководство пользователя страница 10

Brief introduction of functions

- 6 -

II. Brief introduction of functions

WG6500-1 is a series of integrated welding/generating set.

z

The set employs a 50Hz/230VAC generating set with a rated output of 5kW and

maximum output of 5.5 kW, and guarantees a stable and adequate output voltage.

z

The engine’s fuel consumption rate is

≤

370g/kW.h; it is equipped with a 25L large

fuel tank to meet the need of long-time operation.

z

Manual welding, DC argon-arc welding and pulse argon-arc welding are available.

z

Maximum welding current values of manual welding, DC argon-arc welding and

pulse argon-arc welding are respectively 150A, 200A, and 200A (pulse frequency is
30Hz), the current can be adjusted in a continuous way from the minimum value of
15 A to the maximum values; current values are shown in a digital display, and
observation of them is very easy

z

High-frequency arc starting is employed by the argon-arc welding to achieve an

easy arc starting.

z

The total power of the equipment can be used for welding, or 5 kW of it can be all

used for supply to the 50Hz/230VAC power network; in addition, the residual power
during welding can also be used for supply to the external power grid.

z

The welding unit of the set has self-protection functions against over current, under

voltage, and over heating, so that safe work of the equipment is guaranteed.

«
...
8
9
10
11
12
...
»

Содержание WG6500M-1
































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды